IEEE 802.11 Wi-Fi standards

IEEE 802.11 is a set of media access control (MAC) and physical layer (PHY) specifications for implementing wireless local area network (WLAN) computer communication in the 900 MHz and 2.4, 3.6, 5, and 60 GHz frequency bands. They are created and maintained by the Institute of Electrical and Electronics Engineers (IEEE) LAN/MAN Standards Committee (IEEE 802). The base version of the standard was released in 1997, and has had subsequent amendments. The standard and amendments provide the basis for wireless network products using the Wi-Fi brand. While each amendment is officially revoked when it is incorporated in the latest version of the standard, the corporate world tends to market to the revisions because they concisely denote capabilities of their products. As a result, in the market place, each revision tends to become its own standard.

General description
The 802.11 family consists of a series of half-duplex over-the-air modulation techniques that use the same basic protocol. 802.11-1997 was the first wireless networking standard in the family, but 802.11b was the first widely accepted one, followed by 802.11a, 802.11g, 802.11n, and 802.11ac. Other standards in the family (c–f, h, j) are service amendments that are used to extend the current scope of the existing standard, which may also include corrections to a previous specification.[1]

802.11b and 802.11g use the 2.4 GHz ISM band, operating in the United States under Part 15 of the U.S. Federal Communications Commission Rules and Regulations. Because of this choice of frequency band, 802.11b and g equipment may occasionally suffer interference from microwave ovens, cordless telephones, and Bluetooth devices. 802.11b and 802.11g control their interference and susceptibility to interference by using direct-sequence spread spectrum (DSSS) and orthogonal frequency-division multiplexing (OFDM) signalling methods, respectively. 802.11a uses the 5 GHz U-NII band, which, for much of the world, offers at least 23 non-overlapping channels rather than the 2.4 GHz ISM frequency band offering only three non-overlapping channels, where other adjacent channels overlap. Better or worse performance with higher or lower frequencies (channels) may be realized, depending on the environment. 802.11n can use either the 2.4 GHz or the 5 GHz band; 802.11ac uses only the 5 GHz band.

The segment of the radio frequency spectrum used by 802.11 varies between countries. In the US, 802.11a and 802.11g devices may be operated without a license, as allowed in Part 15 of the FCC Rules and Regulations. Frequencies used by channels one through six of 802.11b and 802.11g fall within the 2.4 GHz amateur radio band. Licensed amateur radio operators may operate 802.11b/g devices under Part 97 of the FCC Rules and Regulations, allowing increased power output but not commercial content or encryption.[2]

802.11-1997 (802.11 legacy)
The original version of the standard IEEE 802.11 was released in 1997 and clarified in 1999, but is today obsolete. It specified two net bit rates of 1 or 2 megabits per second (Mbit/s), plus forward error correction code. It specified three alternative physical layer technologies: diffuse infrared operating at 1 Mbit/s; frequency-hopping spread spectrum operating at 1 Mbit/s or 2 Mbit/s; and direct-sequence spread spectrum operating at 1 Mbit/s or 2 Mbit/s. The latter two radio technologies used microwave transmission over the Industrial Scientific Medical frequency band at 2.4 GHz. Some earlier WLAN technologies used lower frequencies, such as the U.S. 900 MHz ISM band.
Legacy 802.11 with direct-sequence spread spectrum was rapidly supplanted and popularized by 802.11b.

802.11a (OFDM waveform)
Originally described as clause 17 of the 1999 specification, the OFDM waveform at 5.8 GHz is now defined in clause 18 of the 2012 specification, and provides protocols that allow transmission and reception of data at rates of 1.5 to 54 Mbit/s. It has seen widespread worldwide implementation, particularly within the corporate workspace. While the original amendment is no longer valid, the term 802.11a is still used by wireless access point (cards and routers) manufacturers to describe interoperability of their systems at 5.8 GHz, 54 Mbit/s.

The 802.11a standard uses the same data link layer protocol and frame format as the original standard, but an OFDM based air interface (physical layer). It operates in the 5 GHz band with a maximum net data rate of 54 Mbit/s, plus error correction code, which yields realistic net achievable throughput in the mid-20 Mbit/s.[3]

Since the 2.4 GHz band is heavily used to the point of being crowded, using the relatively unused 5 GHz band gives 802.11a a significant advantage. However, this high carrier frequency also brings a disadvantage: the effective overall range of 802.11a is less than that of 802.11b/g. In theory, 802.11a signals are absorbed more readily by walls and other solid objects in their path due to their smaller wavelength, and, as a result, cannot penetrate as far as those of 802.11b. In practice, 802.11b typically has a higher range at low speeds (802.11b will reduce speed to 5.5 Mbit/s or even 1 Mbit/s at low signal strengths). 802.11a also suffers from interference,[4] but locally there may be fewer signals to interfere with, resulting in less interference and better throughput.

802.11b
The 802.11b standard has a maximum raw data rate of 11 Mbit/s, and uses the same media access method defined in the original standard. 802.11b products appeared on the market in early 2000, since 802.11b is a direct extension of the modulation technique defined in the original standard. The dramatic increase in throughput of 802.11b (compared to the original standard) along with simultaneous substantial price reductions led to the rapid acceptance of 802.11b as the definitive wireless LAN technology.

Devices using 802.11b experience interference from other products operating in the 2.4 GHz band. Devices operating in the 2.4 GHz range include microwave ovens, Bluetooth devices, baby monitors, cordless telephones, and some amateur radio equipment.

802.11g
In June 2003, a third modulation standard was ratified: 802.11g. This works in the 2.4 GHz band (like 802.11b), but uses the same OFDM based transmission scheme as 802.11a. It operates at a maximum physical layer bit rate of 54 Mbit/s exclusive of forward error correction codes, or about 22 Mbit/s average throughput.[5] 802.11g hardware is fully backward compatible with 802.11b hardware, and therefore is encumbered with legacy issues that reduce throughput by ~21% when compared to 802.11a.

The then-proposed 802.11g standard was rapidly adopted in the market starting in January 2003, well before ratification, due to the desire for higher data rates as well as to reductions in manufacturing costs. By summer 2003, most dual-band 802.11a/b products became dual-band/tri-mode, supporting a and b/g in a single mobile adapter card or access point. Details of making b and g work well together occupied much of the lingering technical process; in an 802.11g network, however, activity of an 802.11b participant will reduce the data rate of the overall 802.11g network.

Like 802.11b, 802.11g devices suffer interference from other products operating in the 2.4 GHz band, for example wireless keyboards.

802.11-2007
In 2003, task group TGma was authorized to “roll up” many of the amendments to the 1999 version of the 802.11 standard. REVma or 802.11ma, as it was called, created a single document that merged 8 amendments (802.11a, b, d, e, g, h, i, j) with the base standard. Upon approval on March 8, 2007, 802.11REVma was renamed to the then-current base standard IEEE 802.11-2007.[6]

802.11n
802.11n is an amendment that improves upon the previous 802.11 standards by adding multiple-input multiple-output antennas (MIMO). 802.11n operates on both the 2.4 GHz and the 5 GHz bands. Support for 5 GHz bands is optional. It operates at a maximum net data rate from 54 Mbit/s to 600 Mbit/s. The IEEE has approved the amendment, and it was published in October 2009.[7][8] Prior to the final ratification, enterprises were already migrating to 802.11n networks based on the Wi-Fi Alliance’s certification of products conforming to a 2007 draft of the 802.11n proposal.

802.11-2012
In 2007, task group TGmb was authorized to “roll up” many of the amendments to the 2007 version of the 802.11 standard. REVmb or 802.11mb, as it was called, created a single document that merged ten amendments (802.11k, r, y, n, w, p, z, v, u, s) with the 2007 base standard. In addition much cleanup was done, including a reordering of many of the clauses.[9] Upon publication on March 29, 2012, the new standard was referred to as IEEE 802.11-2012.

802.11ac
IEEE 802.11ac-2013 is an amendment to IEEE 802.11, published in December 2013, that builds on 802.11n.[10] Changes compared to 802.11n include wider channels (80 or 160 MHz versus 40 MHz) in the 5 GHz band, more spatial streams (up to eight versus four), higher-order modulation (up to 256-QAM vs. 64-QAM), and the addition of Multi-user MIMO (MU-MIMO). As of October 2013, high-end implementations support 80 MHz channels, three spatial streams, and 256-QAM, yielding a data rate of up to 433.3 Mbit/s per spatial stream, 1300 Mbit/s total, in 80 MHz channels in the 5 GHz band.[11] Vendors have announced plans to release so-called “Wave 2” devices with support for 160 MHz channels, four spatial streams, and MU-MIMO in 2014 and 2015.[12][13][14]

802.11ad
IEEE 802.11ad is an amendment that defines a new physical layer for 802.11 networks to operate in the 60 GHz millimeter wave spectrum. This frequency band has significantly different propagation characteristics than the 2.4 GHz and 5 GHz bands where Wi-Fi networks operate. Products implementing the 802.11ad standard are being brought to market under the WiGig brand name. The certification program is now being developed by the Wi-Fi Alliance instead of the now defunct WiGig Alliance.[15] The peak transmission rate of 802.11ad is 7 Gbit/s.[16]

TP-Link announced the world’s first 802.11ad router in January 2016.[17]

802.11af
IEEE 802.11af, also referred to as “White-Fi” and “Super Wi-Fi”,[18] is an amendment, approved in February 2014, that allows WLAN operation in TV white space spectrum in the VHF and UHF bands between 54 and 790 MHz.[19][20] It uses cognitive radio technology to transmit on unused TV channels, with the standard taking measures to limit interference for primary users, such as analog TV, digital TV, and wireless microphones.[20] Access points and stations determine their position using a satellite positioning system such as GPS, and use the Internet to query a geolocation database (GDB) provided by a regional regulatory agency to discover what frequency channels are available for use at a given time and position.[20] The physical layer uses OFDM and is based on 802.11ac.[21] The propagation path loss as well as the attenuation by materials such as brick and concrete is lower in the UHF and VHF bands than in the 2.4 and 5 GHz bands, which increases the possible range.[20] The frequency channels are 6 to 8 MHz wide, depending on the regulatory domain.[20] Up to four channels may be bonded in either one or two contiguous blocks.[20] MIMO operation is possible with up to four streams used for either space–time block code (STBC) or multi-user (MU) operation.[20] The achievable data rate per spatial stream is 26.7 Mbit/s for 6 and 7 MHz channels, and 35.6 Mbit/s for 8 MHz channels.[22] With four spatial streams and four bonded channels, the maximum data rate is 426.7 Mbit/s for 6 and 7 MHz channels and 568.9 Mbit/s for 8 MHz channels.[22]

802.11ah
IEEE 802.11ah defines a WLAN system operating at sub 1 GHz license-exempt bands, with final approval slated for September 2016.[19][23] Due to the favorable propagation characteristics of the low frequency spectra, 802.11ah can provide improved transmission range compared with the conventional 802.11 WLANs operating in the 2.4 GHz and 5 GHz bands. 802.11ah can be used for various purposes including large scale sensor networks,[24] extended range hotspot, and outdoor Wi-Fi for cellular traffic offloading, whereas the available bandwidth is relatively narrow.

802.11ai
IEEE 802.11ai is an amendment to the 802.11 standard that will add new mechanisms for a faster initial link setup time.[25]

802.11aj
IEEE 802.11aj is a rebanding of 802.11ad for use in the 45 GHz unlicensed spectrum available in some regions of the world (specifically China).[25]

802.11aq
IEEE 802.11aq is an amendment to the 802.11 standard that will enable pre-association discovery of services. This extends some of the mechanisms in 802.11u that enabled device discovery to further discover the services running on a device, or provided by a network.[25]

802.11ax
IEEE 802.11ax is the successor to 802.11ac, and will increase the efficiency of WLAN networks. Currently at a very early stage of development this project has the goal of providing 4x the throughput of 802.11ac.[26]

802.11ay
IEEE 802.11ay is a standard that is being developed. It is an amendment that defines a new physical layer for 802.11 networks to operate in the 60 GHz millimeter wave spectrum. It will be an extension of the existing 11ad, aimed to extend the throughput, range and use-cases. The main use-cases include: indoor operation, out-door back-haul and short range communications. The peak transmission rate of 802.11ay is 20 Gbit/s.[27] The main extensions include: channel bonding (2, 3 and 4), MIMO and higher modulation schemes.

References

Wikipedia
IEEE (Institute of Electrical and Electronics Engineers)
American Radio Relay League
cnet (CBS Interactive Inc)
Wi-Fi Alliance
Wi-Fi Planet
LitePoint, a Teradyne company
arXiv, by Cornell University
O’Reilly Media
Wireless Networking in the Developing World
Pudai LLC
PCWorld, IDG Consumer & SMB
Aruba, a Hewlett Packard Enterprise Company
Cisco Systems, Inc
Knowingly Corporation
Ars Technica
Elektrorevue
Rice Networks Group
TTA (Telecommunications Technology Association)
IEEE 802 LAN/MAN Standards Committee
Dailywireless

Footnotes

[1] IEEE-SA Standards Board Operations Manual. IEEE-SA.
[2] ARRLWeb: Part 97 – Amateur Radio Service. American Radio Relay League.
[3] http://www.oreillynet.com/wireless/2003/08/08/wireless_throughput.html
[4] Angelakis, V.; Papadakis, S.; Siris, V.A.; Traganitis, A. (March 2011). “Adjacent channel interference in 802.11a is harmful: Testbed validation of a simple quantification model“. Communications Magazine (IEEE) 49 (3): 160–166. doi:10.1109/MCOM.2011.5723815. ISSN 0163-6804
[5] Wi-Fi Alliance: Organization. Official industry association web site.Wi-Fi Alliance: Organization
[6] Official IEEE 802.11 working group project timelines. June 2, 2014.
[7] IEEE-SA – News & Events. Standards.ieee.org.
[8] IEEE 802.11n-2009—Amendment 5: Enhancements for Higher Throughput. IEEE-SA. 29 October 2009. doi:10.1109/IEEESTD.2009.5307322.
[9] Why did 802.11-2012 renumber clauses?. Matthew Gast, Aerohive Networks.
[10] New IEEE 802.11ac™ Specification Driven by Evolving Market Need for Higher, Multi-User Throughput in Wireless LANs. IEEE.
[11] AC1900: Innovation or 3D Wi-Fi?. SmallNetBuilder.
[12] Quantenna chipset to anchor speedy first ‘Wave 2’ Asus router. PCWorld.
[13] What Wave of 802.11ac is Right for You?. Aruba Networks.
[14] Cisco will ride the 802.11ac Wave2. Cisco Systems.
[15] Wi-Fi Alliance gobbles up WiGig; plans to certify devices this year.
[16] IEEE Standard Association – IEEE Get Program
[17] TP-Link unveils world’s first 802.11ad WiGig router. Ars Technica.
[18] Comparison of 802.11af and 802.22 standards – physical layer and cognitive functionality. elektrorevue.
[19] Official IEEE 802.11 working group project timelines. 2016-03-23.
[20] IEEE 802.11af: A Standard for TV White Space Spectrum Sharing (PDF). IEEE.
[21] TVWS Regulation and Standardization (IEEE 802.11af) (PDF).
[22] TGaf PHY proposal. IEEE P802.11.
[23] P802.11ah Project Authorization Request (PDF). IEEE. 2010-09-30.
[24] 802.11ah: WiFi Standard for 900MHz. dailywireless.org.
[25] IEEE 802.11, The Working Group Setting the Standards for Wireless LANs.
[26] https://mentor.ieee.org/802.11/dcn/14/11-14-0165-01-0hew-802-11-hew-sg-proposed-par.docx
[27] P802.11ay (PDF). IEEE. p. “This amendment defines standardized modifications to both the IEEE 802.11 physical layers (PHY) and the IEEE 802.11 medium access control layer (MAC) that enables at least one mode of operation capable of supporting a maximum throughput of at least 20 gigabits per second (measured at the MAC data service access point), while maintaining or improving the power efficiency per station.”

3 thoughts on “IEEE 802.11 Wi-Fi standards

  1. Hi :). I am from Netherlands and i don’t know how can i disable my signature? Regards 🙂

  2. Hello there.

    Well, let’s begin with finding out what type of device you using and if you are referring to an email signature or something else. Can you let us know?

    We look forward to hearing back from you soon.

    McGrandles IT Support.

  3. Hello there,

    Can you tell us which email program or website you are using and we will do our best to help you step through the process to disable your signature.

    McGrandles IT Solutions.

Comments are closed.